HomeNewsArticle Display

4th EMS Provides Equipment Maintenance to F-15E Strike Eagle, Aerospace Ground Equipment

Airman 1st Class Cote Bidwell, 4th Equipment Maintenance Squadron inspection section journeyman, removes a utility reservoir from an F-15E Strike Eagle, Feb. 4, 2020, at Seymour Johnson Air Force Base, N.C.

Airman 1st Class Cote Bidwell, 4th Equipment Maintenance Squadron inspection section journeyman, removes a utility reservoir from an F-15E Strike Eagle, Feb. 4, 2020, at Seymour Johnson Air Force Base, N.C. Bidwell had to remove the utility reservoir in order to get to a hydraulic line that was broken behind it. (U.S. Air Force photo by Airman First Class Kimberly Barrera)

Airman 1st Class Mathew Castro, 4th Equipment Maintenance aerospace ground equipment apprentice (left), and Airmen 1st Class Drennon Hausman, 4th Equipment Maintenance aerospace ground equipment apprentice (right), clean the wheel bearings on an MHU-83 bomb lift truck, Feb. 4, 2020, at Seymour Johnson Air Force Base, N.C.

Airman 1st Class Mathew Castro, 4th Equipment Maintenance aerospace ground equipment apprentice (left), and Airmen 1st Class Drennon Hausman, 4th Equipment Maintenance aerospace ground equipment apprentice (right), clean the wheel bearings on an MHU-83 bomb lift truck, Feb. 4, 2020, at Seymour Johnson Air Force Base, N.C. The mission of AGE is to support the F-15E Strike Eagle flying operations and maintenance. (U.S. Air Force photo by Airman First Class Kimberly Barrera)

Airman 1st Class Humberto Perez, 4th Equipment Maintenance Squadron non-destructive inspector, uses a stationary mag unit process control with an AS5282 ring to establish a baseline to evaluate system effectiveness, Feb. 4, 2020, at Seymour Johnson Air Force Base, N.C.

Airman 1st Class Humberto Perez, 4th Equipment Maintenance Squadron non-destructive inspector, uses a stationary mag unit process control with an AS5282 ring to establish a baseline to evaluate system effectiveness, Feb. 4, 2020, at Seymour Johnson Air Force Base, N.C. Perez performed this process in order to find the greatest sensitivity to determine whether or not the particle bath should be changed or if its best to keep the same magnetic particle bath. (U.S. Air Force photo by Airman First Class Kimberly Barrera)

Tech. Sgt. Robert Dyson-Cersley, 4th Equipment Maintenance Squadron aircraft structural maintenance production supervisor, bends a fuel sense line tubing assembly using a production tube bender, Feb. 4, 2020, at Seymour Johnson Air Force Base, N.C.

Tech. Sgt. Robert Dyson-Cersley, 4th Equipment Maintenance Squadron aircraft structural maintenance production supervisor, bends a fuel sense line tubing assembly using a production tube bender, Feb. 4, 2020, at Seymour Johnson Air Force Base, N.C. Dyson-Cersley used a sample and engineer drawing to ensure the tubing assembly was bent properly. (U.S. Air Force photo by Airman First Class Kimberly Barrera)

Airmen from the 4th Equipment Maintenance Squadron work on sheet metal training projects at the Aircraft Structural Maintenance shop, Feb. 4, 2020, at Seymour Johnson Air Force Base, N.C.

Airmen from the 4th Equipment Maintenance Squadron work on sheet metal training projects at the Aircraft Structural Maintenance shop, Feb. 4, 2020, at Seymour Johnson Air Force Base, N.C. The training projects provided hands on training for the Airmen. (U.S. Air Force photo by Airman First Class Kimberly Barrera)

Airman 1st Class Lambert Belanders, 4th Equipment Maintenance Squadron metals technology fabrication flight apprentice, uses a mini mill to fabricate an apex bit holder, Feb. 4, 2020, at Seymour Johnson Air Force Base, N.C.

Airman 1st Class Lambert Belanders, 4th Equipment Maintenance Squadron metals technology fabrication flight apprentice, uses a mini mill to fabricate an apex bit holder, Feb. 4, 2020, at Seymour Johnson Air Force Base, N.C. Belanders fabricated the apex bit holder for a consolidated tool kit. (U.S. Air Force photo by Airman First Class Kimberly Barrera)

Airman 1st Class Arnoldo Madrigal, 4th Equipment Maintenance Squadron metals technology fabrication flight apprentice, uses a lathe to fabricate a bushing, Feb. 4, 2020, at Seymour Johnson Air Force Base, N.C.

Airman 1st Class Arnoldo Madrigal, 4th Equipment Maintenance Squadron metals technology fabrication flight apprentice, uses a lathe to fabricate a bushing, Feb. 4, 2020, at Seymour Johnson Air Force Base, N.C. The bushing was designed for a rudder vertical flight control on an F-15E Strike Eagle. (U.S. Air Force photo by Airman First Class Kimberly Barrera)

SEYMOUR JOHNSON AIR FORCE BASE, N.C. -- Airman 1st Class Cote Bidwell, 4th Equipment Maintenance Squadron inspection section journeyman, removes a utility reservoir from an F-15E Strike Eagle, Feb. 4, 2020, at Seymour Johnson Air Force Base, N.C. Bidwell had to remove the utility reservoir in order to get to a hydraulic line that was broken behind it. (U.S. Air Force photo by Airman First Class Kimberly Barrera)
USAF Comments Policy
If you wish to comment, use the text box below. AF reserves the right to modify this policy at any time.

This is a moderated forum. That means all comments will be reviewed before posting. In addition, we expect that participants will treat each other, as well as our agency and our employees, with respect. We will not post comments that contain abusive or vulgar language, spam, hate speech, personal attacks, violate EEO policy, are offensive to other or similar content. We will not post comments that are spam, are clearly "off topic", promote services or products, infringe copyright protected material, or contain any links that don't contribute to the discussion. Comments that make unsupported accusations will also not be posted. The AF and the AF alone will make a determination as to which comments will be posted. Any references to commercial entities, products, services, or other non-governmental organizations or individuals that remain on the site are provided solely for the information of individuals using this page. These references are not intended to reflect the opinion of the AF, DoD, the United States, or its officers or employees concerning the significance, priority, or importance to be given the referenced entity, product, service, or organization. Such references are not an official or personal endorsement of any product, person, or service, and may not be quoted or reproduced for the purpose of stating or implying AF endorsement or approval of any product, person, or service.

Any comments that report criminal activity including: suicidal behaviour or sexual assault will be reported to appropriate authorities including OSI. This forum is not:

  • This forum is not to be used to report criminal activity. If you have information for law enforcement, please contact OSI or your local police agency.
  • Do not submit unsolicited proposals, or other business ideas or inquiries to this forum. This site is not to be used for contracting or commercial business.
  • This forum may not be used for the submission of any claim, demand, informal or formal complaint, or any other form of legal and/or administrative notice or process, or for the exhaustion of any legal and/or administrative remedy.

AF does not guarantee or warrant that any information posted by individuals on this forum is correct, and disclaims any liability for any loss or damage resulting from reliance on any such information. AF may not be able to verify, does not warrant or guarantee, and assumes no liability for anything posted on this website by any other person. AF does not endorse, support or otherwise promote any private or commercial entity or the information, products or services contained on those websites that may be reached through links on our website.

Members of the media are asked to send questions to the public affairs through their normal channels and to refrain from submitting questions here as comments. Reporter questions will not be posted. We recognize that the Web is a 24/7 medium, and your comments are welcome at any time. However, given the need to manage federal resources, moderating and posting of comments will occur during regular business hours Monday through Friday. Comments submitted after hours or on weekends will be read and posted as early as possible; in most cases, this means the next business day.

For the benefit of robust discussion, we ask that comments remain "on-topic." This means that comments will be posted only as it relates to the topic that is being discussed within the blog post. The views expressed on the site by non-federal commentators do not necessarily reflect the official views of the AF or the Federal Government.

To protect your own privacy and the privacy of others, please do not include personally identifiable information, such as name, Social Security number, DoD ID number, OSI Case number, phone numbers or email addresses in the body of your comment. If you do voluntarily include personally identifiable information in your comment, such as your name, that comment may or may not be posted on the page. If your comment is posted, your name will not be redacted or removed. In no circumstances will comments be posted that contain Social Security numbers, DoD ID numbers, OSI case numbers, addresses, email address or phone numbers. The default for the posting of comments is "anonymous", but if you opt not to, any information, including your login name, may be displayed on our site.

Thank you for taking the time to read this comment policy. We encourage your participation in our discussion and look forward to an active exchange of ideas.